型号: PCIe-6363

产品编号: 781051-01

SPECIFICATIONS PCIe-6363

PCI Express, 32 AI (16-Bit, 2 MS/s), 4 AO (2.86 MS/s), 48 DIO

Multifunction I/O Device

Definitions

Warranted specifications describe the performance of a model under stated operating conditions and are covered by the model warranty.






Characteristics describe values that are relevant to the use of the model under stated operating conditions but are not covered by the model warranty.


•         Typical specifications describe the performance met by a majority of models.

•         Nominal specifications describe an attribute that is based on design, conformance testing, or supplemental testing.

Specifications are Typical unless otherwise noted.

Conditions

Specifications are valid at 25 °C unless otherwise noted.

Analog Input

Number of   channels

32 single-ended or 16 differential

ADC   resolution

16 bits

DNL

No missing codes guaranteed

INL

Refer to AI Absolute   Accuracy.

Sample rate

Single   channel maximum

2.00 MSample/s

Multichannel maximum (aggregate)

1.00 MSample/s

Minimum

No minimum

Timing   resolution

10 ns

Timing   accuracy

50 ppm of sample rate

Input   coupling

DC

Input   range

±0.1 V, ±0.2 V, ±0.5 V, ±1   V, ±2 V, ±5 V, ±10 V

Maximum   working voltage for analog inputs (signal + common mode)

±11 V of AI GND

CMRR (DC   to 60 Hz)

100 dB

Figure 1. AI <0..31> CMRR

                             10                         100

        1 k                        10 k

Frequency (Hz)

100 k

Input   impedance



Device   on



AI+ to   AI GND

>10   GΩ in parallel with 100 pF

AI- to   AI GND

>10   GΩ in parallel with 100 pF

Device   off


AI+ to   AI GND

820 Ω

AI- to   AI GND

820 Ω

Input   bias current

±100   pA

Crosstalk (at 100 kHz)

Adjacent   channels

-75 dB

Non-adjacent   channels

-95 dB

Small   signal bandwidth (-3 dB)

1.7 MHz

Figure 2. AI <0..31> Small Signal Bandwidth

Input FIFO size                                               2,047 samples

Scan list   memory

4,095 entries

Data   transfers

DMA (scatter-gather), programmed I/O

Overvoltage protection for all analog input and sense channels

Table 1. Settling Time for Multichannel Measurements

Range

±60 ppm of Step   (±4 LSB for Full-Scale Step)

±15 ppm of Step   (±1 LSB for Full-Scale Step)

± 10 V, ±5 V, ±2 V, ±1 V

1 μs

1.5 μs

±0.5 V

1.5 μs

2 μs

±0.2 V, ±0.1 V

2 μs

8 μs

Figure 3. Settling Error versus Time for Different Source Impedances

1

    10                                                       100

Time (µs)

Analog Triggers

Number of   triggers

1

Source

AI   <0..31>, APFI <0,1>

Functions

Start   Trigger, Reference Trigger,

Pause   Trigger, Sample Clock, Convert Clock,

Sample   Clock Timebase

Source   level


AI   <0..31>

±Full   scale

APFI   <0,1>

±10 V

Resolution

16 bits

Modes

Analog   edge triggering, analog edge triggering with hysteresis, analog window   triggering

Bandwidth   (-3 dB)


AI   <0..31>

3.4 MHz

APFI   <0,1>

3.9 MHz

Accuracy

±1% of   range

APFI   <0,1> characteristics


Input   impedance

10 kΩ

Coupling

DC

Protection

Power   on

±30 V

Power   off

±15 V

AI Absolute Accuracy (Warranted)

Table 2. AI Absolute Accuracy

Nominal

Range

Positive

Full Scale (V)

Nominal Range

Negative

Full Scale (V)

Residual

Gain   Error

(ppm of

Reading)

Residual

Offset

Error (ppm of   Range)

Offset

Tempco

(ppm   of

Range/°C)

Random

Noise,   σ

(μVrms)

Absolute

Accuracy at Full

Scale   (μV)

10

-10

48

13

21

315

1,660

5

-5

55

13

21

157

870

2

-2

55

13

24

64

350

1

-1

65

17

27

38

190

0.5

-0.5

68

17

34

27

100

0.2

-0.2

95

27

55

21

53

0.1

-0.1

108

45

90

17

33

Note Absolute Accuracy at Full Scale is determined using the following assumptions:

•         TempChangeFromLastExternalCal = 10 °C

•         TempChangeFromLastInternalCal = 1 °C

•         NumberOfReadings = 10,000

•         CoverageFactor = 3 σ

Note Accuracies listed are valid for up to two years from the device external calibration.

Gain tempco                                                    13 ppm/°C

Reference   tempco

1 ppm/°C

INL error

60 ppm of range

AI Absolute Accuracy Equation

AbsoluteAccuracy = Reading · (GainError) + Range · (OffsetError) + NoiseUncertainty

GainError = ResidualGainError + GainTempco · (TempChangeFromLastInternalCal) +

ReferenceTempco · (TempChangeFromLastExternalCal)

OffsetError = ResidualOffsetError + OffsetTempco · (TempChangeFromLastInternalCal) + INLError

                                         Random Noise ⋅   3

NoiseUncertainty =  for a coverage factor of 3 σ and averaging 10, 000 10,000 points.

AI Absolute Accuracy Example

For example, on the 10 V range, the absolute accuracy at full scale is as follows:

GainError: 48 ppm + 13 ppm · 1 + 1 ppm · 10 = 71 ppm

OffsetError: 13 ppm + 21 ppm · 1 + 60 ppm = 94 ppm

NoiseUncertainty:  = 9.4 µV

AbsoluteAccuracy: 10 V · (GainError) + 10 V · (OffsetError) + NoiseUncertainty = 1,660 µV

Analog Output

Number of   channels

4

DAC   resolution

16 bits

DNL

±1 LSB

Monotonicty

16 bit guaranteed

Maximum   update rate (simultaneous)


1   channel

2.86 MSample/s

2   channels

2.00 MSample/s

3   channels

1.54 MSample/s

4   channels

1.25 MSample/s

Timing   accuracy

50 ppm of sample rate

Timing   resolution

10 ns

Output   range

±10 V, ±5   V, ±external reference on

APFI <0,1>

Output   coupling

DC

Output   impedance

0.2 Ω

Output   current drive

±5 mA

Overdrive   protection

±25 V

Overdrive   current

26 mA

Power-on   state

±5 mV

Power-on/off   glitch

1.5 V peak for 200 ms

Output FIFO size                                             8,191 samples shared among channels used

Data   transfers

DMA (scatter-gather), programmed I/O

AO   waveform modes

Non-periodic waveform, periodic waveform regeneration mode from   onboard FIFO, periodic waveform regeneration from host buffer including   dynamic update

Settling   time, full-scale step 15 ppm

(1 LSB)

2 µs

Slew   rate

20 V/µs

Glitch   energy at midscale transition,

±10 V   range

10 nV · s

External   Reference


APFI   <0,1> characteristics


Input   impedance

10 kΩ

Coupling

DC

Protection,   device on

±30 V

Protection,   device off

±15 V

Range

±11 V

Slew   rate

20 V/μs

Figure 4. AO <0..3> External Reference Bandwidth

AO Absolute Accuracy (Warranted)

Table 3. AO Absolute Accuracy

Nominal

Range

Positive

Full

Scale

(V)

Nominal Range

Negative

Full

Scale

(V)

Residual

Gain

Error

(ppm   of

Reading)

Gain

Tempco

(ppm/

°C)

Reference

Tempco

(ppm/°C)

Residual

Offset

Error

(ppm   of

Range)

Offset

Tempco

(ppm of Range/

°C)

INL

Error

(ppm of

Range)

Absolute

Accuracy at   Full

Scale

(μV)

10

-10

63

17

1

33

2

64

1,890

5

-5

70

8

1

33

2

64

935

Note Absolute Accuracy at Full Scale numbers are valid immediately following self calibration and assumes the device is operating within 10 °C of the last external calibration.

Note Accuracies listed are valid for up to two years from the device external calibration.

AO Absolute Accuracy Equation

AbsoluteAccuracy = OutputValue · (GainError) + Range · (OffsetError)

GainError = ResidualGainError + GainTempco · (TempChangeFromLastInternalCal) +

ReferenceTempco · (TempChangeFromLastExternalCal)

OffsetError = ResidualOffsetError + OffsetTempco · (TempChangeFromLastInternalCal) + INLError

Digital I/O/PFI

Static   Characteristics

Number of   channels

48 total,   32 (P0.<0..31>),

16 (PFI <0..7>/P1, PFI <8..15>/P2)

Ground   reference

D GND

Direction   control

Each terminal individually programmable as input or output

Pull-down resistor

Typical

50 kΩ

Minimum

20 kΩ

Input   voltage protection

±20 V on up to two pins

      Caution Stresses beyond those listed under the Input voltage protection specification may cause permanent damage to the device.

Waveform Characteristics (Port 0 Only)

Terminals used                                                 Port 0 (P0.<0..31>)

Port/sample   size

Up to 32 bits

Waveform   generation (DO) FIFO

2,047 samples

Waveform   acquisition (DI) FIFO

255 samples

DI   Sample Clock frequency

0 MHz to 10 MHz, system and bus activity dependent

DO   Sample Clock frequency


Regenerate   from FIFO

0 MHz to 10 MHz

Streaming   from memory

0 MHz to 10 MHz, system and bus activity dependent

Data   transfers

DMA (scatter-gather), programmed I/O

Digital   line filter settings

160 ns, 10.24 μs, 5.12 ms, disable

PFI/Port1/Port 2 Functionality

Functionality                                                   Static digital input, static digital output,

timing input, timing output

Timing   output sources

Many AI, AO, counter, DI, DO timing signals

Debounce   filter settings

90 ns, 5.12 μs, 2.56 ms, custom interval, disable; programmable   high and low transitions; selectable per input

Recommended Operating Conditions

Input   high voltage (VIH)


Minimum

2.2 V

Maximum

5.25 V

Input   low voltage (VIL)


Minimum

0 V

Maximum

0.8 V

Output   high current (IOH)


P0.<0..31>

-24 mA maximum

PFI   <0..15>/P1/P2

-16 mA maximum

Output   low current (IOL)


P0.<0..31>

24 mA maximum

PFI   <0..15>/P1/P2

16 mA maximum

Digital I/O   Characteristics

Positive-going   threshold (VT+)

2.2 V maximum

Negative-going   threshold (VT-)

0.8 V minimum

Delta VT   hysteresis (VT+ - VT-)

0.2 V minimum

IIL   input low current (VIN = 0 V)

-10 μA maximum

IIH   input high current (VIN = 5 V)

250 μA maximum

Figure 7. PFI <0..15>/P1/P2: IOH versus VOH

Figure 8. PFI <0..15>/P1/P2: IOL versus VOL

                              0                 0.2                0.4

General-Purpose Count

    0.6                0.8                1.0                1.2

VOL (V)

ers

Number   of counter/timers

4

Resolution

32 bits

Counter measurements                                    Edge counting, pulse, pulse width, semi-period, period, two-edge separation

Position   measurements

X1, X2, X4   quadrature encoding with

Channel Z reloading; two-pulse encoding

Output   applications

Pulse, pulse train with dynamic updates, frequency division,   equivalent time sampling

Internal   base clocks

100 MHz, 20 MHz, 100 kHz

External   base clock frequency

0 MHz to 25 MHz

Base   clock accuracy

50 ppm

Inputs

Gate,   Source, HW_Arm, Aux, A, B, Z,

Up_Down, Sample Clock

Routing   options for inputs

Any PFI, RTSI, analog trigger, many internal signals

FIFO

127 samples per counter

Data   transfers

Dedicated scatter-gather DMA controller for each counter/timer,   programmed I/O

Frequency   Generator


Number   of channels

1

Base   clocks

20 MHz, 10 MHz, 100 kHz

Divisors

1 to 16

Base   clock accuracy

50 ppm

Phase-Locked Loop (PLL)

Number   of PLLs

1

Reference   clock locking frequency


RTSI   <0..7>

10 MHz, 20 MHz

PFI   <0..15>

10 MHz, 20 MHz

Output   of PLL

100 MHz Timebase; other signals   derived from

100 MHz   Timebase including 20 MHz and

100 kHz Timebases

External Digital Triggers

Source

Any PFI, RTSI

Polarity

Software-selectable for most signals

Analog   input function

Start   Trigger, Reference Trigger,

Pause   Trigger, Sample Clock, Convert Clock,

Sample Clock Timebase

Analog   output function

Start   Trigger, Pause Trigger, Sample Clock,

Sample Clock Timebase

Counter/timer   functions

Gate,   Source, HW_Arm, Aux, A, B, Z,

Up_Down, Sample Clock

Digital   waveform generation (DO) function

Start   Trigger, Pause Trigger, Sample Clock,

Sample Clock Timebase

Digital   waveform acquisition (DI) function

Start   Trigger, Reference Trigger,

Pause   Trigger, Sample Clock,

Sample Clock Timebase

Device-to-Device Trigger Bus

Input source                                                       RTSI <0..7>

Output   destination

RTSI <0..7>

Output   selections

10 MHz Clock; frequency generator output; many internal signals

Debounce   filter settings

90 ns, 5.12 μs, 2.56 ms, custom interval, disable; programmable   high and low transitions; selectable per input

Bus Interface


Form   factor

x1 PCI Express, specification v1.1 compliant

Slot   compatibility

x1, x4, x8, and x16 PCI Express slots [1]

DMA   channels

8, can be used for analog input, analog output, digital input,   digital output, counter/timer 0, counter/timer 1, counter/timer 2,   counter/timer 3

Power Requirements

Caution The protection provided by the device can be impaired if the device is used in a manner not described in the X Series User Manual.

Without   disk drive power connector installed


+3.3 V

4.6 W

+12 V

5.4 W

With disk   drive power connector installed


+3.3 V

1.6 W

+12 V

5.4 W

+5 V

15 W

Current Limits


       Caution Exceeding the current limits may cause unpredictable device behavior.

Without   disk drive power connector installed


P0/PFI/P1/P2   and +5 V terminals combined

0.59 A maximum

With   disk drive power connector installed


+5 V   terminal (connector 0)

1 A maximum[2]

+5 V   terminal (connector 1)

1 A maximum2

P0/PFI/P1/P2   combined

1 A maximum

Physical Characteristics

Printed   circuit board dimensions

9.9 × 16.8 cm (3.9 × 6.6 in.) (half-length)

Weight

169 g (5.9 oz)

I/O connectors

Device   connector

68-Pos   Right Angle Dual Stack PCB-Mount

VHDCI (Receptacle)

Cable   connector

68-Pos   Offset IDC Cable Connector (Plug)

(SHC68-*)

Note For more information about the connectors used for DAQ devices, refer to the document, NI DAQ Device Custom Cables, Replacement Connectors, and Screws, by going to ni.com/info and entering the Info Code rdspmb.

Disk drive power connector                                 Standard ATX peripheral connector (not serial

ATA)

Calibration


Recommended   warm-up time

15 minutes

Calibration   interval

2 years

Maximum Working Voltage

Maximum working voltage refers to the signal voltage plus the common-mode voltage.

Channel to earth                                                 11 V, Measurement Category I

Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live electrical supply system that powers equipment. This category is for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated lowvoltage sources, and electronics.

Caution Do not connect the system to signals or use for measurements within Measurement Categories II, III, or IV.

Note Measurement Categories CAT I and CAT O are equivalent. These test and measurement circuits are for other circuits not intended for direct connection to the MAINS building installations of Measurement Categories CAT II, CAT III, or CAT IV.

Environmental

Temperature


Operating

0 °C to 50 °C

Storage

-40 °C to 70 °C

Humidity


Operating

10% to 90% RH, noncondensing

Storage

5% to 95% RH, noncondensing

Pollution   Degree

2

Maximum   altitude

2,000 m

Indoor use only.

Environmental Standards

This product meets the requirements of the following environmental standards for electrical equipment.

•         IEC 60068-2-1 Cold

•         IEC 60068-2-2 Dry heat

•         IEC 60068-2-56 Damp heat (steady state)

Safety Compliance Standards

This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:

•         IEC 61010-1, EN 61010-1

•         UL 61010-1, CSA C22.2 No. 61010-1

Note For UL and other safety certifications, refer to the product label or the Product Certifications and Declarations section.

Electromagnetic Compatibility Standards

This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:

•         EN 61326-1 (IEC 61326-1): Class A emissions; Basic immunity

•         EN 55011 (CISPR 11): Group 1, Class A emissions

•         AS/NZS CISPR 11: Group 1, Class A emissions

•         FCC 47 CFR Part 15B: Class A emissions

•         ICES-001: Class A emissions

Note Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.

Note In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe, Canada, Australia and New Zealand (per CISPR 11) Class A equipment is intended for use only in heavy-industrial locations.

Notice For EMC declarations and certifications, and additional information, refer to the Product Certifications and Declarations section.

This product meets the essential requirements of applicable European Directives, as follows:

•         2014/35/EU; Low-Voltage Directive (safety)

•         2014/30/EU; Electromagnetic Compatibility Directive (EMC)

•         2011/65/EU; Restriction of Hazardous Substances (RoHS)

Product Certifications and Declarations

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for NI products, visit ni.com/ certification, search by model number or product line, and click the appropriate link in the Certification column.

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.

For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

Waste Electrical and Electronic Equipment (WEEE)

    EU Customers At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee. 电子信息产品污染控制管理办法（中国RoHS）

中国客户 National Instruments 符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于 National Instruments 中国 RoHS 合规性信息，请登录 ni.com/environment/rohs_china。(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.

Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.

© 2018 National Instruments. All rights reserved.

377777A-01    October 23, 2018


[1] Some motherboards reserve the x16 slot for graphics use. For PCI Express guidelines, visit ni.com/ info and enter the Info Code pciexpress.

[2] Has self-resetting fuse that opens when current exceeds this specification.